*It is always good to learn something new, isn't it?* I got back from school after few months with our refrigerator damaged. Well, I am not someone that does like cold water. because I do not like it, I do love it. *lol* Well, this was something I was not enjoying, and I could do nothing because I had little or no experience in refrigeration and air conditioning apart from the books that I read back in school. I knew the deep freezer has compressors and condensers filled with refrigerant, a cooling fan to control the temperature in a certain space. I complained several times and after few weeks my mom had to listen to my complaint and she brought in a technician to diagnose and repair the deep freezer since it was not cooling anymore. ## Let me tell you about my refrigerator ---
https://cdn.steemitimages.com/DQmYtyQ1skd5McQYaqrA1FscAPg1XM1DjzZV4ehcGuWkjeg/SquarePic_20180618_09514881.jpg ^{The chest freezer is large: image by me} Well, the image shows the white chest freezer of the maker Haier Thermocool which is said to be assembled in Nigeria. I would try to get the features from the internet to best describe this product. The model of the refrigerator is HTF-371HH, it’s a chest freezer capable of 379 liters, this chest freezer allows for cooling of both small and huge food items. The freezer operates on 220 volts and a 50Hz frequency. It is capable of 100 hours of freeze even after the power supply which means the insulation is very thick and about 75mm thickness of polyurethane. The dimension is 1240×745×855 millimeters. --- https://steemitimages.com/DQmSJFCmiPGGtTrvw93vM77RZsA56t47xh9DbFpbqJxfgoA/n345bdw1tixa4fk7lush.png ## The diagnosis --- After several hours of putting on the refrigerator, it was noticed that the freezer or the regulated area would not become cold, therefore there was the first diagnosis of a refrigerant leak. So, refrigerant was filled into the compressor and the chest freezer was monitored for days. I noticed it cooled for some time before it stopped again which means we either have a problem with the compressor or the refrigerant has once again found a way out of the cycle. Opening the valve, we discovered that there was no more refrigerant in it. The one filled in initially had found its way out into the atmosphere. --- https://steemitimages.com/DQmSJFCmiPGGtTrvw93vM77RZsA56t47xh9DbFpbqJxfgoA/n345bdw1tixa4fk7lush.png ## The problem and the tools used --- The problem was a leak in the evaporator and refill of the refrigerant. The tools used includes * Oxyacetylene flame * Copper pipes 13mm * Hacksaw * Brazing flux * Refrigerant * Screwdriver * scrapper * glue * scrapper * mallet

https://cdn.steemitimages.com/DQmaDHTFMuR5rpR2c5ENydf2WtA1FojKnAXJsRtZ2QZiVEw/SquarePic_20180618_09441562.jpg

https://cdn.steemitimages.com/DQmPNLRZkUbhfzh8DDrSDLaHudmrX86ztm2G63Vtzq5dkk4/SquarePic_20180618_09374292.jpg

^{some of the tools used: image taken by me}

^{some tools used: image by me}

https://cdn.steemitimages.com/DQmVY4pqycbvgcVr4g4B1UhXyAWqXX5J9u2FVVqnnwCFaD4/SquarePic_20180618_09392526.jpg

https://cdn.steemitimages.com/DQmcYzSqvVipvXzL3YzV1EagkipVg4wW5STybccAf3P6roF/SquarePic_20180618_09435450.jpg

^{acetylene flame: image by me}

^{C134 refrigerant : image by me}

https://steemitimages.com/DQmSJFCmiPGGtTrvw93vM77RZsA56t47xh9DbFpbqJxfgoA/n345bdw1tixa4fk7lush.png ## The Job --- The work started with using the screwdriver to uncap the cover of the chest freezer to have access to the inner part of the freezer it wasn’t so difficult getting it off. Next off was removing the caps to gain access to the evaporator. The aluminum foils were the barriers left between the evaporator fins and me. So, I got a scraper to peel off the aluminum files to access the evaporator. After removing the aluminum foil carefully, the polyurethane. The polyurethane is an insulating material used in refrigerators to preserve its temperature or prevent its temperature from rising fast. It is a thick material and white in color. Quite similar to the polystyrene used in packaging of new appliance just like the one in your television. For Nigerians, it is that white stuff you use in making glue. *Lol...familiar now?* Buried at the surface, this is where the evaporator coils are located. I found out the evaporator coils which were made of iron by the company had completely corroded therefore it is prone to leakage or it is even the cause of the refrigerant leak.

^{^{a close look at the first pipe: image taken by me @adetola}}

Therefore, the inlet and the exhaust end of the evaporator coils had to be located, after it had been located, the hacksaw was applied at a comfortable length and the pipe cut. Now what the company (Haier thermocool) did was bad, an iron tube as an evaporator is really bad because, at one point, we all know that refrigeration has to do with water and iron and water are good friends of corrosion and in long term usage, such tube or pipe would definitely lose its property and leak out. This chest freezer was bought five years ago which is a long time and these evaporator fins must be replaced. I bought two coils of evaporator fins which are made of copper due to its resistance to corrosion. You can read more about corrosion from @rharphelle [here.](https://steemit.com/stemng/@rharphelle/corrosion-protection-methods-meet-the-war-lords-against-corrosion)

^{^{brazing the pipe : image taken by me @adetola}}

The next thing I faced was brazing *(brazing involves joining of two similar materials permanently)* this pipes together. This had to be done with the oxyacetylene flame *(the oxyacetylene flame is, of course, the same one that your teacher told you is used for cutting metal. It has a combination of nitrogen and oxygen gas)* it had to be tuned to a proper temperature where it can melt both metals (copper and iron) together alongside the electrode. The electrode used in joining both metals was flux. The flux was applied in the middle while the brazing was going on. The copper pipe had to be expanded first before the iron pipe was put inside to a comfortable length before the flame was applied thereafter the flux was used as the electrode flux to seal the weld. The same way the evaporator coils were coiled all around the insulating wall of the freezer so was the copper coil done and where needed, the brazing process was repeated to ensure continuity of the pipes back to the outlet. Eventually, we did it three times and successfully completed the cycle and tested for a leak.

^{^{filling the compressor: image taken by me @adetola}}

This test for the leak was carried out in a similar way to a non-destructive test type called hydrostatic test, a test gas was passed into the compressor and allowed to circulate then foamy liquid was applied on the surface of all three weld joints. What happens if there is a leak would be a bubble on the surface of the leak while the calm fluid dries off when there is no leak. In this case, the liquid dried off while the test gas which was air was removed from the compressor and allowed to flow out. Fitting the coiled compressor tube was a bit of a problem but with the help of a mallet which was carefully applied at special points with enough support it was able to sit inside the space we removed the corroded pipe from. Replacing the aluminum foil to look like it was before was another task at hand the parts first had to be stretched out on a flat surface using the mallet before the gum is applied on the surface of the insulating material and the aluminum foil to make it stick to the surface carefully. After this is done, the last phase of the teardown is to fill the compressor with the working fluid and this was done by using the inlet of the compressor as it was done before when it was being tested and a certain amount of gas C134 refrigerant was filled into the compressor while the aluminum foil was allowed to dry up. Lastly, the cover of the chest freezer was returned to its place. --- https://steemitimages.com/DQmSJFCmiPGGtTrvw93vM77RZsA56t47xh9DbFpbqJxfgoA/n345bdw1tixa4fk7lush.png ### Image gallery --- You would see some images and a video in my gallery about how these operations are carried out on these materials.

https://cdn.steemitimages.com/DQmYtyQ1skd5McQYaqrA1FscAPg1XM1DjzZV4ehcGuWkjeg/SquarePic_20180618_09514881.jpg

https://cdn.steemitimages.com/DQmavFTPb9pAR2eS7AD3Yyw32xX2HCfD1kfwyZorUmezcuP/SquarePic_20180618_09495721.jpg

^{The chest freezer before teardown: image taken by me}

^{the cover is about to be removed: image by me}

https://cdn.steemitimages.com/DQmTD1xANJm2SQz1hXLniZBC4r3JP4tTZP2S89RdZRNffzu/SquarePic_20180618_09315520.jpg

https://cdn.steemitimages.com/DQmRjwH7Uj88nvPLq4D5pGBuERQZ4FNaQLQ5eezhFaHCuPD/SquarePic_20180618_09341620.jpg

^{removing the aluminum foil: image by me}

^{exposing the aluminum foil : image by me}

https://cdn.steemitimages.com/DQmWB4xes3wew1pB8sDuWDHSmyQgum2BhLgL99NV4vxd7Sq/SquarePic_20180618_09352958.jpg

https://cdn.steemitimages.com/DQmNTGkpMYMFcD5RnyirWitpn35YQzo8SMSsYiu8ABeMK92/SquarePic_20180618_09363491.jpg

^{a closer look at the pipe: image by me}

^{pulling out the corroded pipe: image by me}

https://cdn.steemitimages.com/DQmW1AZ1SnMithiw6uxCzPqfyy5jr7ptK2RATB6G6AeyT4f/SquarePic_20180618_09385970.jpg

https://cdn.steemitimages.com/DQmbAq1NvzhDNq86L644HAPZ6x6zJ3FRQTYjQejuHfkG6A1/SquarePic_20180618_09401725.jpg

^{exposing both ends of the evaporator: image by me}

^{the replacement image by me}

https://cdn.steemitimages.com/DQmRT8djPUGS22Nea7DN91217niZ76iigWoMaccgrZe9X5H/SquarePic_20180618_09405662.jpg

https://cdn.steemitimages.com/DQmVY4pqycbvgcVr4g4B1UhXyAWqXX5J9u2FVVqnnwCFaD4/SquarePic_20180618_09392526.jpg

^{brazing of both pipes: image by me}

^{the acetylene used: image taken by me}

https://cdn.steemitimages.com/DQmPrVtkWeUfTDFvggJDW3yUpfByzZ5Z4yhWEtx5uQcMFkA/SquarePic_20180618_09412083.jpg

https://cdn.steemitimages.com/DQme56we8PqZrzyKkdSoRB1xDDdGv3sc8NXd639mVPTPger/SquarePic_20180618_09424999.jpg

^{flux used in brazing of both pipes: image by me}

^{laying the pipe: image taken by me}

https://cdn.steemitimages.com/DQmcKYJ4xbMgYhTnJeUrvnfbcJ8qxA5Vsr84vCHsfWHHkmx/SquarePic_20180618_09464888.jpg

https://cdn.steemitimages.com/DQmUV4o4PGH13PeMUZevVFz2JqYtCZmPV2TUV4V2RuFuNKc/SquarePic_20180618_09491822.jpg

^{stretching the aluminum foil: image by me}

^{replacement of the foil: image taken by me}

https://cdn.steemitimages.com/DQmPftjZDmnaBdmXCSYJGQgHhidtqh1wBNUXchdzSYi1yyj/SquarePic_20180618_09511778.jpg

https://cdn.steemitimages.com/DQmcYzSqvVipvXzL3YzV1EagkipVg4wW5STybccAf3P6roF/SquarePic_20180618_09435450.jpg

^{completely replaced : image by me}

^{the c134 refrigerant: image taken by me}

https://cdn.steemitimages.com/DQmVjeWwFoRkZCYQUt5dq6GwDCLPV9LBJGGSZmYQU15hJJx/SquarePic_20180618_09461898.jpg

https://cdn.steemitimages.com/DQmcDyb5SHzgH9rz1yTjkJnhpJKNYgBBY66DpxbbF5pyrJw/SquarePic_20180618_09523261.jpg

^{refilling of the refrigerant: image by me}

^{a job well done: image taken by me}

watch this video I made to see several operations being carried out https://youtu.be/0mQNooG67gs --- https://steemitimages.com/DQmSJFCmiPGGtTrvw93vM77RZsA56t47xh9DbFpbqJxfgoA/n345bdw1tixa4fk7lush.png ## Conclusion/ testing --- The chest freezer after several hours was put to test by connecting to a power source and monitored for several hours. This teardown and repair had brought about a drastic change to the refrigerator as its working fine with the exchange of temperature between both atmospheres happening as to its failure before. I was happy I finally had knowledge about refrigeration and what I was able to pinpoint is that a refrigerator is just a couple of tubes with a compressor and condenser. The only thing that makes your refrigerator big is the controlled area or space which you call your refrigerator. This job took almost 6 hours to complete. I hope you enjoyed reading. --- https://steemitimages.com/DQmSJFCmiPGGtTrvw93vM77RZsA56t47xh9DbFpbqJxfgoA/n345bdw1tixa4fk7lush.png ## References --- Knowledge is the beginning of all good things in life, it is a process and it is being improved upon here are the books and links I read. + [refrigerator specs](https://www.decorhubng.com/shop/haier-thermocool-large-chest-freezer-htf-379h-2/) + [Wikipedia brazing](https://en.m.wikipedia.org/wiki/Brazing) + [basic refrigeration cycle](http://www.air-conditioning-and-refrigeration-guide.com/refrigeration-cycle.html) + A Textbook of Refrigeration and Air Conditioning By R.S. Khurmi And J.K Gupta. ---

^{If you write STEM (Science, Technology, Engineering, and Mathematics) related posts, consider joining [#steemSTEM](https://steemit.com/trending/steemstem) on steemit chat or discord [here](https://discord.gg/vwzWz3Z). If you are from Nigeria, you may want to include the [#stemng](https://steemit.com/trending/stemng) tag in your post. You can visit this [blog](https://steemit.com/@stemng) by @stemng for more details.

![SteemSTEM](https://steemitimages.com/0x0/https://i.imgur.com/WhYkkh9.gif)

^{You can also join us at Promo-Mentors, to improve your blogging skills. Join our [discord channel](https://discord.gg/xrugFe) and meet awesome mentors who are willing and ready to shape your writing skills.

https://steemitimages.com/DQmTDLNSwrxM4R85rA2qsR18pugncTy5FDhVf5gJBoW5vLm/signature.gif}}